
Scodeno SFP SM 13-LC20 Gbic 1Gb
Artikelnr. Sco_GS1D-13-LC20-I
- Gbic 1Gb SFP
- 20km glasvezel
- Single mode
- LC connector
- Hoort bij 15-LC20
Op voorraad (6)
Bestel nu, wij verzenden morgen.
6 op voorraad (kan nabesteld worden)
- 15 jaar Intercel-partner
- Persoonlijk advies, 085 401 9230
Gecontroleerd doorFrans Maas Specificaties
| XPTN-GS1D-15-LC20-I/XPTN-GS1D-13-LC20-I | |
|---|---|
| 1.25Gbps, BIDI, SFP Optical Transceiver, 20K m, DDM | |
| 1. Feature: | |
| l SFP package with LC connector | |
l 1310nm FP Laser and 1550nm PIN
photodetector | |
| l 1550nm DFB Laser and 1310nm PIN photodetector | |
| l Up to 20Km transmission on SMF | |
| l +3.3V single power supply | |
| l LVPECL compatible data input/output interface | |
| l Low EMI and excellent ESD protection | |
| l laser safety standard IEC-60825 compliant | |
| l Compatible with RoHS | |
| l Compatible with SFF8472 | |
| 2. Application: | |
| l Ethernet | |
| l Telecom | |
| l Fiber Channel | |
| 3. Absolute Maximum Ratings: | |
| Parameter | Symbol Minimum Maximum Units |
| Storage Temperature | Tst -40 +85 °C |
| Supply Voltage | Vcc 0 +3.6 V |
| Operating Relative Humidity | RH 5 95 % |
| 4. Operation Environment: | |
|---|---|
| Parameter | Symbol Min Typical Max Units |
| Supply Voltage | Vcc 3.15 3.3 3.45 V |
| Operating Case Temperature | TC 0 +70 ℃ |
| Power Dissipation | 1 W |
| Data Rate | 1.25 Gbps |
| 5. Optical Characteristics: | |
| Parameter | Symbol Min. Typ. Max. Units |
| Transmitter Section | |
| Center Wavelength | Tx 1310 lo 1260 1310 1360 nm |
| Tx 1550 | 1540 1550 1560 |
| Spectral Width(RMS) | Tx 1310 Dl - - 4 nm |
| Tx 1550 | 1 |
| Average Output Power | Tx 1310 Po -9 - -3 dBm |
| Tx 1550 | -9 -3 |
| Extinction Ratio | Er 8 - 15 dB |
| Rise/Fall Time(20%~80%) | Tr/Tf 0.26 ns |
| Total jitter | Tj 0.43 UI |
| Optical Eye Diagram | IEEE 802.3z and ANSI Fibre Channel Compatible |
| Receiver Section | |
| Center Wavelength | Rx 1550 lo 1500 1550 1600 nm |
| Rx 1310 | 1260 1310 1360 |
| Receiver Sensitivity | Rsen -22 dBm |
| Receiver Overload | Rov -3 dBm |
| Return Loss | 12 dB |
| LOS Assert | LOSA -36 dBm |
| LOS Dessert | LOSD -23 dBm |
| LOS Hysteresis | 0.5 5 |
| (Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V) | |
| 6. Electrical Characteristics: | |
| (Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V) | |
| Parameter | Symbol Min. Typ. Max. unit |
| Transmitter Section | |
| Input Differential Impendence | Zin 90 100 110 Ohm |
| Data Input Swing Differential | Vin 500 2400 mV |
| TX Disable | Disable 2.0 Vcc V |
| Enable | 0 0.8 V |
| TX Fault | Assert 2.0 Vcc V |
| Deassert | 0 0.8 V |
| Receiver Section | |
| Output differential impendence | Zout 100 Ohm |
| Data Input Swing Differential | Vout 370 2000 mV |
| Rx_LOS | Assert 2.0 Vcc V |
| Deassert | 0 0.8 V |
| 7. EEPROM INFORMATION(A0): | |
| Addr | Field Size
(Bytes) |
| 0 | 1 Identifier 03 SFP |
| 1 | 1 Ext. Identifier 04 MOD4 |
| 2 | 1 Connector 07 LC |
| 3-10 | 8 Transceiver 00 00 00 02 12 00 0D 01 Transmitter Code |
| 11 | 1 Encoding 01 8B10B |
| 12 | 1 BR, nominal 0D 1250M bps |
| 13 | 1 Reserved 00 |
| 14 | 1 Length (9um)-km 14 20km |
| 15 | 1 Length (9um) 64/C8/FF |
| 16 | 1 Length (50um) 00 |
| 17 | 1 Length (62.5um) 00 |
| 18 | 1 Length (copper) 00 |
| 19 | 1 Reserved 00 |
| 20-35 | 16 Vendor name 57 49 4E 54 4F 50 20 20 20 20 20 20 20 20 20 20 |
| 36 | 1 Reserved 00 |
| 37-39 | 3 Vendor OUI 00 00 00 |
| 40-55 | 16 Vendor PN xx xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx |
| 56-59 | 4 Vendor rev 31 2E 30 20 V1.0 |
| 60-61 | 2 Wavelength 05 1E/05 D2 1310nm/1550nm |
| 62 | 1 Reserved 00 |
| 63 | 1 CC BASE XX Check sum of byte 0~62 |
| 64-65 | 2 Options 00 1A LOS, TX_DISABLE, TX_FAULT |
| 66 | 1 BR, max 32 50% |
| 67 | 1 BR, min 32 50% |
| 68-83 | 16 Vendor SN 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| 84-91 | 8 Vendor date code XX XX XX 20 Year, Month, Day |
| 92-94 | 3 Reserved 00 |
| 95 | 1 CC_EXT XX Check sum of byte 64~94 |
| 96-255 | 160 Vendor specific |
| 8. Diagnostics: | |
| Parameter | Range Accuracy Unit Calibration |
| Temperature | 0 ~ 70 ±3 ºC Internal |
| Voltage | 0 ~ VCC 0.1 V Internal |
| Bias Current | 10 ~ 80 ±2 mA Internal |
| Tx Power | -9 ~ -3 ±2 dBm Internal |
| Rx Power | -28~-3 ±3 dBm Internal |
| 9. Pin Description: | |
| Pins | Name Discription NOTE |
| 1 | VeeT Transmitter Ground |
| 2 | Tx Fault Transmitter Fault Indication 1 |
| 3 | Tx Disable Transmitter Disable 2 |
| 4 | MOD DEF2 Module Definition 2 3 |
| 5 | MOD DEF1 Module Definition 1 3 |
| 6 | MOD DEF0 Module Definition 0 3 |
| 7 | Rate Select Not Connected |
| 8 | LOS Loss of Signal 4 |
| 9 | VeeR Receiver Ground |
| 10 | VeeR Receiver Ground |
| 11 | VeeR Receiver Ground |
| 12 | RD- Inv. Received Data Output 5 |
| 13 | RD+ IReceived Data Output 5 |
| 14 | VeeR Receiver Ground |
| 15 | VccR Receiver Power |
| 16 | VccT Transmitter Power |
| 17 | VeeT Transmitter Ground |
| 18 | TD+ Transmit Data Input 6 |
| 19 | TD- Inv. Transmit Data Input 6 |
| 20 | VeeT Transmitter Ground |
| Notes: | |
| 1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V. | |
| 2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are: | |
| Low (0~0.8V): Transmitter on | |
| (>0.8V, <2.0V): Undefined | |
| High (2.0~3.3V): Transmitter Disabled | |
| Open: Transmitter Disabled | |
| 3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on | |
| the host board. The pull-up voltage shall be VccT or VccR. | |
| MOD-DEF 0 is grounded by the module to indicate that the module is present | |
| MOD-DEF 1 is the clock line of two wire serial interface for serial ID | |
| MOD-DEF 2 is the data line of two wire serial interface for serial ID | |
| 4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V. | |
| 5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. | |
| 6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. | |
| 10. Recommended Application Circuit: | |
| 11. Outline drawing (mm): | |
| XPTN-GS1D-15-LC20-I/XPTN-GS1D-13-LC20-I | |
| 1.25Gbps, BIDI, SFP Optical Transceiver, 20K m, DDM | |
| 1. Feature: | |
| l SFP package with LC connector | |
l 1310nm FP Laser and 1550nm PIN
photodetector | |
| l 1550nm DFB Laser and 1310nm PIN photodetector | |
| l Up to 20Km transmission on SMF | |
| l +3.3V single power supply | |
| l LVPECL compatible data input/output interface | |
| l Low EMI and excellent ESD protection | |
| l laser safety standard IEC-60825 compliant | |
| l Compatible with RoHS | |
| l Compatible with SFF8472 | |
| 2. Application: | |
| l Ethernet | |
| l Telecom | |
| l Fiber Channel | |
| 3. Absolute Maximum Ratings: | |
| Parameter | Symbol Minimum Maximum Units |
| Storage Temperature | Tst -40 +85 °C |
| Supply Voltage | Vcc 0 +3.6 V |
| Operating Relative Humidity | RH 5 95 % |
| 4. Operation Environment: | |
| Parameter | Symbol Min Typical Max Units |
| Supply Voltage | Vcc 3.15 3.3 3.45 V |
| Operating Case Temperature | TC 0 +70 ℃ |
| Power Dissipation | 1 W |
| Data Rate | 1.25 Gbps |
| 5. Optical Characteristics: | |
| Parameter | Symbol Min. Typ. Max. Units |
| Transmitter Section | |
| Center Wavelength | Tx 1310 lo 1260 1310 1360 nm |
| Tx 1550 | 1540 1550 1560 |
| Spectral Width(RMS) | Tx 1310 Dl - - 4 nm |
| Tx 1550 | 1 |
| Average Output Power | Tx 1310 Po -9 - -3 dBm |
| Tx 1550 | -9 -3 |
| Extinction Ratio | Er 8 - 15 dB |
| Rise/Fall Time(20%~80%) | Tr/Tf 0.26 ns |
| Total jitter | Tj 0.43 UI |
| Optical Eye Diagram | IEEE 802.3z and ANSI Fibre Channel Compatible |
| Receiver Section | |
| Center Wavelength | Rx 1550 lo 1500 1550 1600 nm |
| Rx 1310 | 1260 1310 1360 |
| Receiver Sensitivity | Rsen -22 dBm |
| Receiver Overload | Rov -3 dBm |
| Return Loss | 12 dB |
| LOS Assert | LOSA -36 dBm |
| LOS Dessert | LOSD -23 dBm |
| LOS Hysteresis | 0.5 5 |
| (Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V) | |
| 6. Electrical Characteristics: | |
| (Ambient Operating Temperature 0°C to +70°C, Vcc =3.3 V) | |
| Parameter | Symbol Min. Typ. Max. unit |
| Transmitter Section | |
| Input Differential Impendence | Zin 90 100 110 Ohm |
| Data Input Swing Differential | Vin 500 2400 mV |
| TX Disable | Disable 2.0 Vcc V |
| Enable | 0 0.8 V |
| TX Fault | Assert 2.0 Vcc V |
| Deassert | 0 0.8 V |
| Receiver Section | |
| Output differential impendence | Zout 100 Ohm |
| Data Input Swing Differential | Vout 370 2000 mV |
| Rx_LOS | Assert 2.0 Vcc V |
| Deassert | 0 0.8 V |
| 7. EEPROM INFORMATION(A0): | |
| Addr | Field Size
(Bytes) |
| 0 | 1 Identifier 03 SFP |
| 1 | 1 Ext. Identifier 04 MOD4 |
| 2 | 1 Connector 07 LC |
| 3-10 | 8 Transceiver 00 00 00 02 12 00 0D 01 Transmitter Code |
| 11 | 1 Encoding 01 8B10B |
| 12 | 1 BR, nominal 0D 1250M bps |
| 13 | 1 Reserved 00 |
| 14 | 1 Length (9um)-km 14 20km |
| 15 | 1 Length (9um) 64/C8/FF |
| 16 | 1 Length (50um) 00 |
| 17 | 1 Length (62.5um) 00 |
| 18 | 1 Length (copper) 00 |
| 19 | 1 Reserved 00 |
| 20-35 | 16 Vendor name 57 49 4E 54 4F 50 20 20 20 20 20 20 20 20 20 20 |
| 36 | 1 Reserved 00 |
| 37-39 | 3 Vendor OUI 00 00 00 |
| 40-55 | 16 Vendor PN xx xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx |
| 56-59 | 4 Vendor rev 31 2E 30 20 V1.0 |
| 60-61 | 2 Wavelength 05 1E/05 D2 1310nm/1550nm |
| 62 | 1 Reserved 00 |
| 63 | 1 CC BASE XX Check sum of byte 0~62 |
| 64-65 | 2 Options 00 1A LOS, TX_DISABLE, TX_FAULT |
| 66 | 1 BR, max 32 50% |
| 67 | 1 BR, min 32 50% |
| 68-83 | 16 Vendor SN 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
| 84-91 | 8 Vendor date code XX XX XX 20 Year, Month, Day |
| 92-94 | 3 Reserved 00 |
| 95 | 1 CC_EXT XX Check sum of byte 64~94 |
| 96-255 | 160 Vendor specific |
| 8. Diagnostics: | |
| Parameter | Range Accuracy Unit Calibration |
| Temperature | 0 ~ 70 ±3 ºC Internal |
| Voltage | 0 ~ VCC 0.1 V Internal |
| Bias Current | 10 ~ 80 ±2 mA Internal |
| Tx Power | -9 ~ -3 ±2 dBm Internal |
| Rx Power | -28~-3 ±3 dBm Internal |
| 9. Pin Description: | |
| Pins | Name Discription NOTE |
| 1 | VeeT Transmitter Ground |
| 2 | Tx Fault Transmitter Fault Indication 1 |
| 3 | Tx Disable Transmitter Disable 2 |
| 4 | MOD DEF2 Module Definition 2 3 |
| 5 | MOD DEF1 Module Definition 1 3 |
| 6 | MOD DEF0 Module Definition 0 3 |
| 7 | Rate Select Not Connected |
| 8 | LOS Loss of Signal 4 |
| 9 | VeeR Receiver Ground |
| 10 | VeeR Receiver Ground |
| 11 | VeeR Receiver Ground |
| 12 | RD- Inv. Received Data Output 5 |
| 13 | RD+ IReceived Data Output 5 |
| 14 | VeeR Receiver Ground |
| 15 | VccR Receiver Power |
| 16 | VccT Transmitter Power |
| 17 | VeeT Transmitter Ground |
| 18 | TD+ Transmit Data Input 6 |
| 19 | TD- Inv. Transmit Data Input 6 |
| 20 | VeeT Transmitter Ground |
| Notes: | |
| 1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V. | |
| 2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are: | |
| Low (0~0.8V): Transmitter on | |
| (>0.8V, <2.0V): Undefined | |
| High (2.0~3.3V): Transmitter Disabled | |
| Open: Transmitter Disabled | |
| 3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on | |
| the host board. The pull-up voltage shall be VccT or VccR. | |
| MOD-DEF 0 is grounded by the module to indicate that the module is present | |
| MOD-DEF 1 is the clock line of two wire serial interface for serial ID | |
| MOD-DEF 2 is the data line of two wire serial interface for serial ID | |
| 4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V. | |
| 5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. | |
| 6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. | |
| 10. Recommended Application Circuit: | |
| 11. Outline drawing (mm): | |
Omschrijving
De glasvezel Gbic GS1D-13-LC20-I 1Gb van Scodeno past in alle Scodeno units met een SFP poort en voldoet aan de gangbare eisen om tevens geschikt te zijn voor andere switches en/of mediaconverters.
De GS1D-13-LC20I heeft een zend-golflengte van 1310nm en een ontvangst-golflengte van 1550nm.
De GS1D-15-LC20-I heeft een zend-golflengte van 1550nm en een ontvangst-golflengte van 1310nm
Op deze manier kunnen de twee Gbics over een single mode glasvezelkabel communiceren.
De glasvezellengte is maximaal 20 kilometer,
De Scodeno producten zijn Exclusief verkrijgbaar bij shop4power.nl
Voor alle scodeno producten verwijzen wij naar: https://shop4power.nl/s/merken/scodeno/
Vragen
Wanneer wordt mijn bestelling verzonden?
Op een werkdag vóór 15:00 uur besteld, verzenden we dezelfde dag nog. Na 15:00 uur of in het weekend verzenden we de volgende werkdag.
Zijn de prijzen exclusief btw?
Ja. De winkelprijs is exclusief btw. U ziet ook het bedrag inclusief btw. De productgegevens voor zoekmachines gebruiken de prijs exclusief btw.
Kan ik een oud typenummer opzoeken?
Ja. Op de homepage zoekt u een Wetac- of Intercel-nummer. U komt bij de opvolger uit als die in de shop staat.



